HardwareSerial.cpp

#include <stdlib.h>
#include <stdio.h>
#include <string.h>
#include <inttypes.h>

#include "pins_arduino.h"
#include "io_pin_remap.h"
#include "HardwareSerial.h"
#include "soc/soc_caps.h"
#include "driver/uart.h"
#include "freertos/queue.h"

#ifndef ARDUINO_SERIAL_EVENT_TASK_STACK_SIZE
#define ARDUINO_SERIAL_EVENT_TASK_STACK_SIZE 2048
#endif

#ifndef ARDUINO_SERIAL_EVENT_TASK_PRIORITY
#define ARDUINO_SERIAL_EVENT_TASK_PRIORITY (configMAX_PRIORITIES-1)
#endif

#ifndef ARDUINO_SERIAL_EVENT_TASK_RUNNING_CORE
#define ARDUINO_SERIAL_EVENT_TASK_RUNNING_CORE -1
#endif

void serialEvent(void) __attribute__((weak));
void serialEvent(void) {}

#if SOC_UART_NUM > 1
void serialEvent1(void) __attribute__((weak));
void serialEvent1(void) {}
#endif /* SOC_UART_NUM > 1 */

#if SOC_UART_NUM > 2
void serialEvent2(void) __attribute__((weak));
void serialEvent2(void) {}
#endif /* SOC_UART_NUM > 2 */

#if !defined(NO_GLOBAL_INSTANCES) && !defined(NO_GLOBAL_SERIAL)
#if ARDUINO_USB_CDC_ON_BOOT //Serial used for USB CDC
HardwareSerial Serial0(0);
#else
HardwareSerial Serial(0);
#endif
#if SOC_UART_NUM > 1
HardwareSerial Serial1(1);
#endif
#if SOC_UART_NUM > 2
HardwareSerial Serial2(2);
#endif

void serialEventRun(void)
{
#if HWCDC_SERIAL_IS_DEFINED == 1        // Hardware JTAG CDC Event
    if(HWCDCSerial.available()) HWCDCSerialEvent();
#endif    
#if USB_SERIAL_IS_DEFINED == 1          // Native USB CDC Event
    if(USBSerial.available()) USBSerialEvent();
#endif    
    // UART0 is default serialEvent()
    if(Serial.available()) serialEvent();
#if SOC_UART_NUM > 1
    if(Serial1.available()) serialEvent1();
#endif
#if SOC_UART_NUM > 2
    if(Serial2.available()) serialEvent2();
#endif
}
#endif

#if !CONFIG_DISABLE_HAL_LOCKS
#define HSERIAL_MUTEX_LOCK()    do {} while (xSemaphoreTake(_lock, portMAX_DELAY) != pdPASS)
#define HSERIAL_MUTEX_UNLOCK()  xSemaphoreGive(_lock)
#else
#define HSERIAL_MUTEX_LOCK()
#define HSERIAL_MUTEX_UNLOCK()
#endif

HardwareSerial::HardwareSerial(uint8_t uart_nr) :
_uart_nr(uart_nr),
_uart(NULL),
_rxBufferSize(256),
_txBufferSize(0),
_onReceiveCB(NULL),
_onReceiveErrorCB(NULL),
_onReceiveTimeout(false),
_rxTimeout(2),
_rxFIFOFull(0),
_eventTask(NULL)
#if !CONFIG_DISABLE_HAL_LOCKS
    ,_lock(NULL)
#endif
{
#if !CONFIG_DISABLE_HAL_LOCKS
    if(_lock == NULL){
        _lock = xSemaphoreCreateMutex();
        if(_lock == NULL){
            log_e("xSemaphoreCreateMutex failed");
            return;
        }
    }
#endif
    // do the same as boot time, that will set default UART0 pins RX, TX. 
    if(uart_nr == 0) uartSetPins(0, SOC_RX0, SOC_TX0, -1, -1);
}

HardwareSerial::~HardwareSerial()
{
    end(); // explicit Full UART termination
#if !CONFIG_DISABLE_HAL_LOCKS
    if(_lock != NULL){
        vSemaphoreDelete(_lock);
    }
#endif
}


void HardwareSerial::_createEventTask(void *args)
{
    // Creating UART event Task
    xTaskCreateUniversal(_uartEventTask, "uart_event_task", ARDUINO_SERIAL_EVENT_TASK_STACK_SIZE, this, ARDUINO_SERIAL_EVENT_TASK_PRIORITY, &_eventTask, ARDUINO_SERIAL_EVENT_TASK_RUNNING_CORE);
    if (_eventTask == NULL) {
        log_e(" -- UART%d Event Task not Created!", _uart_nr);
    }
}

void HardwareSerial::_destroyEventTask(void)
{
    if (_eventTask != NULL) {
        vTaskDelete(_eventTask);
        _eventTask = NULL;
    }
}

void HardwareSerial::onReceiveError(OnReceiveErrorCb function)
{
    HSERIAL_MUTEX_LOCK();
    // function may be NULL to cancel onReceive() from its respective task
    _onReceiveErrorCB = function;
    // this can be called after Serial.begin(), therefore it shall create the event task
    if (function != NULL && _uart != NULL && _eventTask == NULL) {
        _createEventTask(this);
    }
    HSERIAL_MUTEX_UNLOCK();
}

void HardwareSerial::onReceive(OnReceiveCb function, bool onlyOnTimeout)
{
    HSERIAL_MUTEX_LOCK();
    // function may be NULL to cancel onReceive() from its respective task
    _onReceiveCB = function;

    // setting the callback to NULL will just disable it
    if (_onReceiveCB != NULL) {
        // When Rx timeout is Zero (disabled), there is only one possible option that is callback when FIFO reaches 120 bytes
        _onReceiveTimeout = _rxTimeout > 0 ? onlyOnTimeout : false;

        // in case that onReceive() shall work only with RX Timeout, FIFO shall be high
        // this is a work around for an IDF issue with events and low FIFO Full value (< 3)
        if (_onReceiveTimeout) {
            uartSetRxFIFOFull(_uart, 120);
            log_w("OnReceive is set to Timeout only, thus FIFO Full is now 120 bytes.");
        }

        // this method can be called after Serial.begin(), therefore it shall create the event task
        if (_uart != NULL && _eventTask == NULL) {
            _createEventTask(this); // Create event task
        }
    }
    HSERIAL_MUTEX_UNLOCK();
}

// This function allow the user to define how many bytes will trigger an Interrupt that will copy RX FIFO to the internal RX Ringbuffer
// ISR will also move data from FIFO to RX Ringbuffer after a RX Timeout defined in HardwareSerial::setRxTimeout(uint8_t symbols_timeout)
// A low value of FIFO Full bytes will consume more CPU time within the ISR
// A high value of FIFO Full bytes will make the application wait longer to have byte available for the Stkech in a streaming scenario
// Both RX FIFO Full and RX Timeout may affect when onReceive() will be called
bool HardwareSerial::setRxFIFOFull(uint8_t fifoBytes)
{
    HSERIAL_MUTEX_LOCK();
    // in case that onReceive() shall work only with RX Timeout, FIFO shall be high
    // this is a work around for an IDF issue with events and low FIFO Full value (< 3)
    if (_onReceiveCB != NULL && _onReceiveTimeout) {
        fifoBytes = 120;
        log_w("OnReceive is set to Timeout only, thus FIFO Full is now 120 bytes.");
    }
    bool retCode = uartSetRxFIFOFull(_uart, fifoBytes); // Set new timeout
    if (fifoBytes > 0 && fifoBytes < SOC_UART_FIFO_LEN - 1) _rxFIFOFull = fifoBytes;
    HSERIAL_MUTEX_UNLOCK();
    return retCode;
}

// timout is calculates in time to receive UART symbols at the UART baudrate.
// the estimation is about 11 bits per symbol (SERIAL_8N1)
bool HardwareSerial::setRxTimeout(uint8_t symbols_timeout)
{
    HSERIAL_MUTEX_LOCK();

    // Zero disables timeout, thus, onReceive callback will only be called when RX FIFO reaches 120 bytes
    // Any non-zero value will activate onReceive callback based on UART baudrate with about 11 bits per symbol
    _rxTimeout = symbols_timeout;
    if (!symbols_timeout) _onReceiveTimeout = false;  // only when RX timeout is disabled, we also must disable this flag

    bool retCode = uartSetRxTimeout(_uart, _rxTimeout); // Set new timeout

    HSERIAL_MUTEX_UNLOCK();
    return retCode;
}

void HardwareSerial::eventQueueReset()
{
    QueueHandle_t uartEventQueue = NULL;
    if (_uart == NULL) {
        return;
    }
    uartGetEventQueue(_uart, &uartEventQueue);
    if (uartEventQueue != NULL) {
        xQueueReset(uartEventQueue);
    }
}

void HardwareSerial::_uartEventTask(void *args)
{
    HardwareSerial *uart = (HardwareSerial *)args;
    uart_event_t event;
    QueueHandle_t uartEventQueue = NULL;
    uartGetEventQueue(uart->_uart, &uartEventQueue);
    if (uartEventQueue != NULL) {
        for(;;) {
            //Waiting for UART event.
            if(xQueueReceive(uartEventQueue, (void * )&event, (TickType_t)portMAX_DELAY)) {
                hardwareSerial_error_t currentErr = UART_NO_ERROR;
                switch(event.type) {
                    case UART_DATA:
                        if(uart->_onReceiveCB && uart->available() > 0 &&
                            ((uart->_onReceiveTimeout && event.timeout_flag) || !uart->_onReceiveTimeout) )
                                uart->_onReceiveCB();
                        break;
                    case UART_FIFO_OVF:
                        log_w("UART%d FIFO Overflow. Consider adding Hardware Flow Control to your Application.", uart->_uart_nr);
                        currentErr = UART_FIFO_OVF_ERROR;
                        break;
                    case UART_BUFFER_FULL:
                        log_w("UART%d Buffer Full. Consider increasing your buffer size of your Application.", uart->_uart_nr);
                        currentErr = UART_BUFFER_FULL_ERROR;
                        break;
                    case UART_BREAK:
                        log_w("UART%d RX break.", uart->_uart_nr);
                        currentErr = UART_BREAK_ERROR;
                        break;
                    case UART_PARITY_ERR:
                        log_w("UART%d parity error.", uart->_uart_nr);
                        currentErr = UART_PARITY_ERROR;
                        break;
                    case UART_FRAME_ERR:
                        log_w("UART%d frame error.", uart->_uart_nr);
                        currentErr = UART_FRAME_ERROR;
                        break;
                    default:
                        log_w("UART%d unknown event type %d.", uart->_uart_nr, event.type);
                        break;
                }
                if (currentErr != UART_NO_ERROR) {
                    if(uart->_onReceiveErrorCB) uart->_onReceiveErrorCB(currentErr);
                }
            }
        }
    }
    vTaskDelete(NULL);
}

void HardwareSerial::begin(unsigned long baud, uint32_t config, int8_t rxPin, int8_t txPin, bool invert, unsigned long timeout_ms, uint8_t rxfifo_full_thrhd)
{
    if(_uart_nr >= SOC_UART_NUM) {
        log_e("Serial number is invalid, please use a number from 0 to %u", SOC_UART_NUM - 1);
        return;
    }

#if !CONFIG_DISABLE_HAL_LOCKS
    if(_lock == NULL){
        log_e("MUTEX Lock failed. Can't begin.");
        return;
    }
#endif

    HSERIAL_MUTEX_LOCK();
    // First Time or after end() --> set default Pins
    if (!uartIsDriverInstalled(_uart)) {
        // get previously used RX/TX pins, if any.
        int8_t _rxPin = uart_get_RxPin(_uart_nr);
        int8_t _txPin = uart_get_TxPin(_uart_nr);
        switch (_uart_nr) {
            case UART_NUM_0:
                if (rxPin < 0 && txPin < 0) {
                    // do not change RX0/TX0 if it has already been set before
                    rxPin = _rxPin < 0 ? (int8_t)SOC_RX0 : _rxPin;
                    txPin = _txPin < 0 ? (int8_t)SOC_TX0 : _txPin;
                }
            break;
#if SOC_UART_NUM > 1                   // may save some flash bytes...
            case UART_NUM_1:
               if (rxPin < 0 && txPin < 0) {
                    // do not change RX1/TX1 if it has already been set before
                    rxPin = _rxPin < 0 ? (int8_t)RX1 : _rxPin;
                    txPin = _txPin < 0 ? (int8_t)TX1 : _txPin;
                }
            break;
#endif
#if SOC_UART_NUM > 2                   // may save some flash bytes...
            case UART_NUM_2:
               if (rxPin < 0 && txPin < 0) {
                    // do not change RX2/TX2 if it has already been set before
                    rxPin = _rxPin < 0 ? (int8_t)RX2 : _rxPin;
                    txPin = _txPin < 0 ? (int8_t)TX2 : _txPin;
                }
            break;
#endif
        }
    }

    // map logical pins to GPIO numbers
    rxPin = digitalPinToGPIONumber(rxPin);
    txPin = digitalPinToGPIONumber(txPin);
    // IDF UART driver keeps Pin setting on restarting. Negative Pin number will keep it unmodified.
    // it will detach previous UART attached pins

    // indicates that uartbegin() has to initilize a new IDF driver
    if (_testUartBegin(_uart_nr, baud ? baud : 9600, config, rxPin, txPin, _rxBufferSize, _txBufferSize, invert, rxfifo_full_thrhd)) {
        _destroyEventTask(); // when IDF uart driver must be restarted, _eventTask must finish too
    }

    // IDF UART driver keeps Pin setting on restarting. Negative Pin number will keep it unmodified.
    // it will detach previous UART attached pins
    _uart = uartBegin(_uart_nr, baud ? baud : 9600, config, rxPin, txPin, _rxBufferSize, _txBufferSize, invert, rxfifo_full_thrhd);
    if (_uart == NULL) {
        log_e("UART driver failed to start. Please check the logs.");
        HSERIAL_MUTEX_UNLOCK();
        return;
    }
    if (!baud) {
        // using baud rate as zero, forces it to try to detect the current baud rate in place
        uartStartDetectBaudrate(_uart);
        time_t startMillis = millis();
        unsigned long detectedBaudRate = 0;
        while(millis() - startMillis < timeout_ms && !(detectedBaudRate = uartDetectBaudrate(_uart))) {
            yield();
        }

        if(detectedBaudRate) {
            delay(100); // Give some time...
            _uart = uartBegin(_uart_nr, detectedBaudRate, config, rxPin, txPin, _rxBufferSize, _txBufferSize, invert, rxfifo_full_thrhd);
#if CONFIG_IDF_TARGET_ESP32C3 || CONFIG_IDF_TARGET_ESP32S3
           // S3 and C3 have a limitation and both can't detect a baud rate lower than 9600
           if (detectedBaudRate == 9600) log_w("The baud detected, as 9600, may be wrong. ESP32-C3 and ESP32-S3 can't detect a baud rate under 9600.");
#endif
        } else {
            log_e("Could not detect baudrate. Serial data at the port must be present within the timeout for detection to be possible");
            _uart = NULL;
        }
    }
    // create a task to deal with Serial Events when, for example, calling begin() twice to change the baudrate,
    // or when setting the callback before calling begin()
    if (_uart != NULL && (_onReceiveCB != NULL || _onReceiveErrorCB != NULL) && _eventTask == NULL) {
        _createEventTask(this);
    }

    // Set UART RX timeout
    uartSetRxTimeout(_uart, _rxTimeout);

    // Set UART FIFO Full depending on the baud rate.
    // Lower baud rates will force to emulate byte-by-byte reading
    // Higher baud rates will keep IDF default of 120 bytes for FIFO FULL Interrupt
    // It can also be changed by the application at any time
    if (!_rxFIFOFull) {    // it has not being changed before calling begin()
      //  set a default FIFO Full value for the IDF driver
      uint8_t fifoFull = 1;
      if (baud > 57600 || (_onReceiveCB != NULL && _onReceiveTimeout)) {
        fifoFull = 120;
      }
      uartSetRxFIFOFull(_uart, fifoFull);
      _rxFIFOFull = fifoFull;
    }

    HSERIAL_MUTEX_UNLOCK();
}

void HardwareSerial::updateBaudRate(unsigned long baud)
{
    uartSetBaudRate(_uart, baud);
}

void HardwareSerial::end()
{
    // default Serial.end() will completely disable HardwareSerial,
    // including any tasks or debug message channel (log_x()) - but not for IDF log messages!
    _onReceiveCB = NULL;
    _onReceiveErrorCB = NULL;
    if (uartGetDebug() == _uart_nr) {
        uartSetDebug(0);
    }
    _rxFIFOFull = 0;
    uartEnd(_uart_nr);  // fully detach all pins and delete the UART driver
    _destroyEventTask(); // when IDF uart driver is deleted, _eventTask must finish too
    _uart = NULL;
}

void HardwareSerial::setDebugOutput(bool en)
{
    if(_uart == 0) {
        return;
    }
    if(en) {
        uartSetDebug(_uart);
    } else {
        if(uartGetDebug() == _uart_nr) {
            uartSetDebug(NULL);
        }
    }
}

int HardwareSerial::available(void)
{
    return uartAvailable(_uart);
}
int HardwareSerial::availableForWrite(void)
{
    return uartAvailableForWrite(_uart);
}

int HardwareSerial::peek(void)
{
    if (available()) {
        return uartPeek(_uart);
    }
    return -1;
}

int HardwareSerial::read(void)
{
    uint8_t c = 0;
    if (uartReadBytes(_uart, &c, 1, 0) == 1) {
        return c;
    } else {
        return -1;
    }
}

// read characters into buffer
// terminates if size characters have been read, or no further are pending
// returns the number of characters placed in the buffer
// the buffer is NOT null terminated.
size_t HardwareSerial::read(uint8_t *buffer, size_t size)
{
    return uartReadBytes(_uart, buffer, size, 0);
}

// Overrides Stream::readBytes() to be faster using IDF
size_t HardwareSerial::readBytes(uint8_t *buffer, size_t length)
{
    return uartReadBytes(_uart, buffer, length, (uint32_t)getTimeout());
}

void HardwareSerial::flush(void)
{
    uartFlush(_uart);
}

void HardwareSerial::flush(bool txOnly)
{
    uartFlushTxOnly(_uart, txOnly);
}

size_t HardwareSerial::write(uint8_t c)
{
    uartWrite(_uart, c);
    return 1;
}

size_t HardwareSerial::write(const uint8_t *buffer, size_t size)
{
    uartWriteBuf(_uart, buffer, size);
    return size;
}

uint32_t  HardwareSerial::baudRate()
{
    return uartGetBaudRate(_uart);
}
HardwareSerial::operator bool() const
{
    return uartIsDriverInstalled(_uart);
}

void HardwareSerial::setRxInvert(bool invert)
{
    uartSetRxInvert(_uart, invert);
}

// negative Pin value will keep it unmodified
// can be called after or before begin()
bool HardwareSerial::setPins(int8_t rxPin, int8_t txPin, int8_t ctsPin, int8_t rtsPin)
{
    // map logical pins to GPIO numbers
    rxPin = digitalPinToGPIONumber(rxPin);
    txPin = digitalPinToGPIONumber(txPin);
    ctsPin = digitalPinToGPIONumber(ctsPin);
    rtsPin = digitalPinToGPIONumber(rtsPin);

    // uartSetPins() checks if pins are valid and, if necessary, detaches the previous ones
    return uartSetPins(_uart_nr, rxPin, txPin, ctsPin, rtsPin);
}

// Enables or disables Hardware Flow Control using RTS and/or CTS pins 
// must use setAllPins() in order to set RTS/CTS pins
// SerialHwFlowCtrl = UART_HW_FLOWCTRL_DISABLE, UART_HW_FLOWCTRL_RTS, 
//                    UART_HW_FLOWCTRL_CTS, UART_HW_FLOWCTRL_CTS_RTS
bool HardwareSerial::setHwFlowCtrlMode(SerialHwFlowCtrl mode, uint8_t threshold)
{
    return uartSetHwFlowCtrlMode(_uart, mode, threshold);
}

// Sets the uart mode in the esp32 uart for use with RS485 modes 
// HwFlowCtrl must be disabled and RTS pin set
// SerialMode = UART_MODE_UART, UART_MODE_RS485_HALF_DUPLEX, UART_MODE_IRDA, 
// or testing mode: UART_MODE_RS485_COLLISION_DETECT, UART_MODE_RS485_APP_CTRL 
bool HardwareSerial::setMode(SerialMode mode)
{
    return uartSetMode(_uart, mode);
}

// minimum total RX Buffer size is the UART FIFO space (128 bytes for most SoC) + 1. IDF imposition.
size_t HardwareSerial::setRxBufferSize(size_t new_size) {

    if (_uart) {
        log_e("RX Buffer can't be resized when Serial is already running. Set it before calling begin().");
        return 0;
    }

    if (new_size <= SOC_UART_FIFO_LEN) {
        log_w("RX Buffer set to minimum value: %d.", SOC_UART_FIFO_LEN + 1);  // ESP32, S2, S3 and C3 means higher than 128
        new_size = SOC_UART_FIFO_LEN + 1;
    }

    _rxBufferSize = new_size;
    return _rxBufferSize;
}

// minimum total TX Buffer size is the UART FIFO space (128 bytes for most SoC).
size_t HardwareSerial::setTxBufferSize(size_t new_size) {

    if (_uart) {
        log_e("TX Buffer can't be resized when Serial is already running. Set it before calling begin().");
        return 0;
    }

    if (new_size <= SOC_UART_FIFO_LEN) {
        log_w("TX Buffer set to minimum value: %d.", SOC_UART_FIFO_LEN);  // ESP32, S2, S3 and C3 means higher than 128
        _txBufferSize = 0; // it will use just UART FIFO with SOC_UART_FIFO_LEN bytes (128 for most SoC)
        return SOC_UART_FIFO_LEN;
    }
    // if new_size is higher than SOC_UART_FIFO_LEN, TX Ringbuffer will be active and it will be used to report back "availableToWrite()"
    _txBufferSize = new_size;
    return _txBufferSize;
}